I've collected several ready-to-run locos since they have started to become available in 009 and Hexworthy is an ideal place to run them. However, as with the Peco coaches, there is something about a pristine RTR loco that jars in a layout setting. They are just too clean. Now I don't want to model heavily weathered almost derelict locos, I'm modelling a preserved railway setting so locos would be kept clean, but even so a working loco will not be box-fresh pristine as soot settles from above, paint dulls due to heat, oil builds up on and near moving parts, and brake and track dirt is thrown up from below.
So here's my attempt at making Exe look used but clean. If you can't tell much difference from a fresh model, that's kind of the point, but subtle differences are there.
Having had issues with enamel-based washes starting to lift the lining on Nesta (fortunately recovered) and not having good results with dilute acrylics I was looking for a new solution. I've a couple of Vallejo ready-to-use washes which work well, but having seen the results of someone using water-soluble oil paints I thought I'd try them. The paints are found in art shops. A little paint is dissolved in water and used as a wash, the concentration can be varied as can how much is applied, but it can also be removed with a damp brush, cotton bud or kitchen towel while damp meaning it is very controllable. I've used a dirty brown mix on underframes and buffer beams, and black in spots where soot/oil might accumulate (like between boiler and side tanks), over brass and copper (it tones them down nicely) and on the motion too.
With my recent increase in confidence with the airbrush I took the brave decision to use it for weathering locos. As with the coaches I've used a mid brown misted very lightly over frames and buffer beams, and black misted very lightly over the cab roof, smokebox, footplate, and a little over the boiler and tank tops. This is done by winding in the "end stop" at the tail of the airbrush (it probably has a proper name) until the needle stops opening with just a faint mist emerging, this means I can spray without risking a wobbly finger causing an unexpected splurge of paint. Better to spend time building up a level of weathering than accidentally overdoing it. The down-side is such a small nozzle opening can block up so every so often the stop is unwound, the needle opened fully and paint sprayed until it is flowing easily again, before winding the stop back in.
I've also painted another batch of people, including crew figures from Faller, Dapol, and Model-U. There are also some "civilians" at the back which I will come back to later.
So here's Exe from another angle. I may have overdone the track dirt up the rear, but the sides remain clean. The motion and pipework are toned down and look oily, while the cab roof, tank top and footplate are a more matt, sooty finish. The boiler top is a little sooty too. Hopefully a superficially clean but used look. A Dapol figure stands in the cab, getting him in was like getting a ship in a bottle! I figured one was enough, and still allows some of the interior detail to be seen. Finally, the bunkers have been filled with crushed coal.
The Kato Prince comes with "brass" knobs to fit to the sand pots and tender, these are on a sprue "tool" which is cut off the main sprue and used to place the knob in the hole before being twisted off. Spares are provided which is useful as I broke one in the wrong place, but it is the work of a few minutes to fit them. I also glued a strip of microstrip to the vertical support for the slide bars, as the flat metal looked a bit too flat.
The can is tiny. Fortunately, it is easy to unclip (removing the blower pipe first helps), but even using Faller HO figures they needed their feet and heads filing down until they fitted under the (overscale thickness) roof. Of course, once in there they can hardly be seen, but nor can the basic interior. I installed a figure in the tender too, as often seen on the prototype! The plastic addition to the slide bar support was painted with gunmetal metalcote, as were some details under the cab.
Again, the weathering aim is clean but used. A hint of the dark wash around the whistles, dome, and tank filler plus a misting of airbrushed "soot" makes the top of the tank look like it betrays a hard day's work, but not neglect. Real coal was added over the moulded plastic load. I've also fitted staples to the Peco coupling droppers for magnetic uncoupling.
Next time, the rest of the RTR loco fleet...
No comments:
Post a Comment